Cable
LMR200 Times
End A
MCX MALE
End B
RP-SMA MALE
Specs Summary
100 ft LMR200 Times — MCX MALE to RP-SMA MALE
LMR200 Times cable assembly, 100 feet, with MCX MALE and RP-SMA MALE connectors. Hand-assembled, tested, and ships free within the US.
100 ft — MCX MALE / RP-SMA MALE
$174.30
Free shipping • In stock
Other lengths:
Signal Loss — 100 ft
Approximate insertion loss for this 100 ft LMR200 Times assembly at common RF frequencies.
| Frequency | Loss / 100 ft | Loss — 100 ft |
|---|---|---|
| 100 MHz | 3 dB | 3 dB |
| 450 MHz | 6.6 dB | 6.6 dB |
| 900 MHz | 9.5 dB | 9.5 dB |
| 1.8 GHz | 13.9 dB | 13.9 dB |
| 2.4 GHz | 16.2 dB | 16.2 dB |
| 5.8 GHz | 27 dB | 27 dB |
About This Assembly
LMR200 Times Cable
LMR-200 is a Times Microwave 50-ohm flexible coaxial cable with a 0.200" diameter, positioned between LMR-195 and LMR-240 for applications requiring a compromise between flexibility and low loss. It supports frequencies up to 3 GHz and is frequently deployed for WLAN access point drops, panel antenna leads, and base station jumpers up to 50 feet.
MCX Connector
MCX (Micro Coaxial) is a snap-on RF connector approximately 30% smaller than SMB, designed for compact equipment requiring frequent connections in a small footprint. Rated to 6 GHz, MCX is commonly used in GPS receivers, automotive telematics modules, handheld communication devices, and compact measurement instruments.
RP-SMA Connector
RP-SMA (Reverse Polarity SMA) uses the SMA threaded coupling mechanism but with the male/female pin convention reversed — the jack has a pin and the plug has a socket. Originally standardized to prevent connection of uncertified antennas to consumer WiFi equipment, RP-SMA is now the dominant connector on commercial WiFi routers, access points, and 2.4/5 GHz antennas.
Common Applications
This MCX and RP-SMA cable assembly is well suited for WLAN access point drops, panel antenna leads, and medium-length indoor runs. The combination of reliable MCX and RP-SMA connectors and custom-cut cable length makes it a practical choice for both field installations and bench setups. Every assembly is hand-terminated, continuity tested, and ships free within the USA.
Frequently Asked Questions
Is this cable hand-assembled in the USA?
Yes. Every CoaxRF cable assembly is hand-terminated and continuity tested at our US facility before shipping. We do not drop-ship pre-made cables from overseas — each cable is built to order.
Can I order a different length than 100 ft?
Yes. This page is for the 100 ft assembly. Use the length buttons above to select a different standard length, or use the Cable Builder for any custom length.
How much signal loss will I see with this 100 ft cable?
At 1800 MHz, LMR200 Times loses approximately 13.9 dB per 100 ft. This 100 ft assembly will have roughly 13.9 dB of insertion loss at that frequency. See the signal loss table for all frequency points.
What is the maximum frequency for this assembly?
This assembly is rated DC – 6 GHz. The effective frequency limit is set by the lowest-rated component — either the cable or one of the connectors. Both MCX MALE and RP-SMA MALE connectors must be within spec at your target frequency.
What is your return policy?
We accept returns within 30 days of delivery. Custom-length cables are accepted as long as they are in original condition. Contact us and we will provide a prepaid return label at no charge.
