Cable
LMR240 Times
End A
RP-SMA MALE
End B
SMA FEMALE
Specs Summary
50 ft LMR240 Times — RP-SMA MALE to SMA FEMALE
LMR240 Times cable assembly, 50 feet, with RP-SMA MALE and SMA FEMALE connectors. Hand-assembled, tested, and ships free within the US.
50 ft — RP-SMA MALE / SMA FEMALE
$107.73
Free shipping • In stock
Other lengths:
Signal Loss — 50 ft
Approximate insertion loss for this 50 ft LMR240 Times assembly at common RF frequencies.
| Frequency | Loss / 100 ft | Loss — 50 ft |
|---|---|---|
| 100 MHz | 2.4 dB | 1.2 dB |
| 450 MHz | 5.3 dB | 2.65 dB |
| 900 MHz | 7.5 dB | 3.75 dB |
| 1.8 GHz | 10.8 dB | 5.4 dB |
| 2.4 GHz | 12.6 dB | 6.3 dB |
| 5.8 GHz | 20.6 dB | 10.3 dB |
About This Assembly
LMR240 Times Cable
LMR-240 is a Times Microwave 50-ohm low-loss coaxial cable with a 0.240" outer diameter and excellent flexibility for its size. Designed for medium-length runs up to 75 feet, it is widely deployed in cellular infrastructure, public safety radio, GPS distribution, and anywhere a balance of low loss and easy installation is required.
RP-SMA Connector
RP-SMA (Reverse Polarity SMA) uses the SMA threaded coupling mechanism but with the male/female pin convention reversed — the jack has a pin and the plug has a socket. Originally standardized to prevent connection of uncertified antennas to consumer WiFi equipment, RP-SMA is now the dominant connector on commercial WiFi routers, access points, and 2.4/5 GHz antennas.
SMA Connector
SMA (SubMiniature version A) is the most widely used RF connector in the industry, offering a threaded interface that provides a secure, low-reflection connection from DC to 18 GHz. Its compact size, 50-ohm impedance, and broad frequency range make it the default choice for WiFi equipment, software-defined radios, cellular antennas, GPS receivers, and RF test instruments.
Common Applications
This RP-SMA and SMA cable assembly is well suited for medium-length antenna runs, public safety radio, and cellular infrastructure jumpers. The combination of reliable RP-SMA and SMA connectors and custom-cut cable length makes it a practical choice for both field installations and bench setups. Every assembly is hand-terminated, continuity tested, and ships free within the USA.
Frequently Asked Questions
Is this cable hand-assembled in the USA?
Yes. Every CoaxRF cable assembly is hand-terminated and continuity tested at our US facility before shipping. We do not drop-ship pre-made cables from overseas — each cable is built to order.
Can I order a different length than 50 ft?
Yes. This page is for the 50 ft assembly. Use the length buttons above to select a different standard length, or use the Cable Builder for any custom length.
How much signal loss will I see with this 50 ft cable?
At 1800 MHz, LMR240 Times loses approximately 10.8 dB per 100 ft. This 50 ft assembly will have roughly 5.4 dB of insertion loss at that frequency. See the signal loss table for all frequency points.
What is the maximum frequency for this assembly?
This assembly is rated DC – 6 GHz. The effective frequency limit is set by the lowest-rated component — either the cable or one of the connectors. Both RP-SMA MALE and SMA FEMALE connectors must be within spec at your target frequency.
What is your return policy?
We accept returns within 30 days of delivery. Custom-length cables are accepted as long as they are in original condition. Contact us and we will provide a prepaid return label at no charge.
