Cable
RFC400
End A
RP-TNC MALE
End B
SO239 UHF Female
Specs Summary
6 ft RFC400 — RP-TNC MALE to SO239 UHF Female
RFC400 cable assembly, 6 feet, with RP-TNC MALE and SO239 UHF Female connectors. Hand-assembled, tested, and ships free within the US.
6 ft — RP-TNC MALE / SO239 UHF Female
$29.48
Free shipping • In stock
Other lengths:
Signal Loss — 6 ft
Approximate insertion loss for this 6 ft RFC400 assembly at common RF frequencies.
| Frequency | Loss / 100 ft | Loss — 6 ft |
|---|---|---|
| 100 MHz | 1.5 dB | 0.09 dB |
| 450 MHz | 3.3 dB | 0.2 dB |
| 900 MHz | 4.7 dB | 0.28 dB |
| 1.8 GHz | 6.8 dB | 0.41 dB |
| 2.4 GHz | 7.9 dB | 0.47 dB |
| 5.8 GHz | 13 dB | 0.78 dB |
About This Assembly
RFC400 Cable
RFC-400 is a cost-effective 0.400" 50-ohm low-loss coaxial cable serving as a value-oriented alternative to LMR-400. It delivers strong performance on runs from 50 to 200 feet and is popular for cellular repeater trunk cables, outdoor antenna feedlines, and budget-conscious infrastructure deployments.
RP-TNC Connector
RP-TNC (Reverse Polarity TNC) uses the TNC threaded shell with reversed pin conventions, similar to RP-SMA. It is used on some commercial WiFi access points and outdoor CPE antennas, particularly in older Cisco and Linksys equipment, and offers better vibration resistance than RP-SMA in demanding outdoor environments.
UHF Connector
The UHF connector (also known as PL-259 male / SO-239 female) is a large, low-cost RF connector designed in the 1930s for HF and VHF frequencies. Despite its name, its practical usable range is below 300 MHz due to its non-constant impedance design. It remains extremely popular in amateur radio (HF through VHF), CB radio, and marine radio applications.
Common Applications
This RP-TNC and UHF cable assembly is well suited for cost-effective long antenna runs, cellular repeater trunk cables, and outdoor feedlines. The combination of reliable RP-TNC and UHF connectors and custom-cut cable length makes it a practical choice for both field installations and bench setups. Every assembly is hand-terminated, continuity tested, and ships free within the USA.
Frequently Asked Questions
Is this cable hand-assembled in the USA?
Yes. Every CoaxRF cable assembly is hand-terminated and continuity tested at our US facility before shipping. We do not drop-ship pre-made cables from overseas — each cable is built to order.
Can I order a different length than 6 ft?
Yes. This page is for the 6 ft assembly. Use the length buttons above to select a different standard length, or use the Cable Builder for any custom length.
How much signal loss will I see with this 6 ft cable?
At 1800 MHz, RFC400 loses approximately 6.8 dB per 100 ft. This 6 ft assembly will have roughly 0.41 dB of insertion loss at that frequency. See the signal loss table for all frequency points.
What is the maximum frequency for this assembly?
This assembly is rated DC – 300 MHz. The effective frequency limit is set by the lowest-rated component — either the cable or one of the connectors. Both RP-TNC MALE and SO239 UHF Female connectors must be within spec at your target frequency.
What is your return policy?
We accept returns within 30 days of delivery. Custom-length cables are accepted as long as they are in original condition. Contact us and we will provide a prepaid return label at no charge.
