Cable
RG174
End A
RP-SMA MALE
End B
RP-TNC MALE
Specs Summary
1 ft RG174 — RP-SMA MALE to RP-TNC MALE
RG174 cable assembly, 1 feet, with RP-SMA MALE and RP-TNC MALE connectors. Hand-assembled, tested, and ships free within the US.
1 ft — RP-SMA MALE / RP-TNC MALE
$12.98
Free shipping • In stock
Other lengths:
Signal Loss — 1 ft
Approximate insertion loss for this 1 ft RG174 assembly at common RF frequencies.
| Frequency | Loss / 100 ft | Loss — 1 ft |
|---|---|---|
| 100 MHz | 6.6 dB | 0.07 dB |
| 450 MHz | 14.5 dB | 0.15 dB |
| 900 MHz | 21.5 dB | 0.22 dB |
| 1.8 GHz | 32 dB | 0.32 dB |
| 2.4 GHz | 38 dB | 0.38 dB |
| 5.8 GHz | 65 dB | 0.65 dB |
About This Assembly
RG174 Cable
RG-174 is an ultra-thin, highly flexible 50-ohm coaxial cable with a 0.100" outer diameter — one of the smallest coax types available. Its stranded center conductor and single-braid shield make it ideal for tight internal wiring where space is at a premium. Typical uses include GPS antenna pigtails, WiFi module connections, and short adapter leads inside enclosures.
RP-SMA Connector
RP-SMA (Reverse Polarity SMA) uses the SMA threaded coupling mechanism but with the male/female pin convention reversed — the jack has a pin and the plug has a socket. Originally standardized to prevent connection of uncertified antennas to consumer WiFi equipment, RP-SMA is now the dominant connector on commercial WiFi routers, access points, and 2.4/5 GHz antennas.
RP-TNC Connector
RP-TNC (Reverse Polarity TNC) uses the TNC threaded shell with reversed pin conventions, similar to RP-SMA. It is used on some commercial WiFi access points and outdoor CPE antennas, particularly in older Cisco and Linksys equipment, and offers better vibration resistance than RP-SMA in demanding outdoor environments.
Common Applications
This RP-SMA and RP-TNC cable assembly is well suited for GPS and WiFi module pigtails, short flexible adapter leads, and internal device wiring. The combination of reliable RP-SMA and RP-TNC connectors and custom-cut cable length makes it a practical choice for both field installations and bench setups. Every assembly is hand-terminated, continuity tested, and ships free within the USA.
Frequently Asked Questions
Is this cable hand-assembled in the USA?
Yes. Every CoaxRF cable assembly is hand-terminated and continuity tested at our US facility before shipping. We do not drop-ship pre-made cables from overseas — each cable is built to order.
Can I order a different length than 1 ft?
Yes. This page is for the 1 ft assembly. Use the length buttons above to select a different standard length, or use the Cable Builder for any custom length.
How much signal loss will I see with this 1 ft cable?
At 1800 MHz, RG174 loses approximately 32 dB per 100 ft. This 1 ft assembly will have roughly 0.32 dB of insertion loss at that frequency. See the signal loss table for all frequency points.
What is the maximum frequency for this assembly?
This assembly is rated DC – 3 GHz. The effective frequency limit is set by the lowest-rated component — either the cable or one of the connectors. Both RP-SMA MALE and RP-TNC MALE connectors must be within spec at your target frequency.
What is your return policy?
We accept returns within 30 days of delivery. Custom-length cables are accepted as long as they are in original condition. Contact us and we will provide a prepaid return label at no charge.
