Cable
RG316DS
End A
PL259 UHF Male
End B
RP-SMA FEMALE
Specs Summary
1 ft RG316DS — PL259 UHF Male to RP-SMA FEMALE
RG316DS cable assembly, 1 feet, with PL259 UHF Male and RP-SMA FEMALE connectors. Hand-assembled, tested, and ships free within the US.
1 ft — PL259 UHF Male / RP-SMA FEMALE
$17.18
Free shipping • In stock
Other lengths:
Signal Loss — 1 ft
Approximate insertion loss for this 1 ft RG316DS assembly at common RF frequencies.
| Frequency | Loss / 100 ft | Loss — 1 ft |
|---|---|---|
| 100 MHz | 5.3 dB | 0.05 dB |
| 450 MHz | 12 dB | 0.12 dB |
| 900 MHz | 17.5 dB | 0.18 dB |
| 1.8 GHz | 26 dB | 0.26 dB |
| 2.4 GHz | 30.5 dB | 0.31 dB |
| 5.8 GHz | 52 dB | 0.52 dB |
About This Assembly
RG316DS Cable
RG-316DS is a double-shielded version of RG-316, featuring two braid layers over the PTFE dielectric for superior EMI isolation. This construction reduces signal leakage and interference pickup, making it essential in sensitive receiver chains, spectrum analyzers, and high-density RF wiring where crosstalk must be minimized.
UHF Connector
The UHF connector (also known as PL-259 male / SO-239 female) is a large, low-cost RF connector designed in the 1930s for HF and VHF frequencies. Despite its name, its practical usable range is below 300 MHz due to its non-constant impedance design. It remains extremely popular in amateur radio (HF through VHF), CB radio, and marine radio applications.
RP-SMA Connector
RP-SMA (Reverse Polarity SMA) uses the SMA threaded coupling mechanism but with the male/female pin convention reversed — the jack has a pin and the plug has a socket. Originally standardized to prevent connection of uncertified antennas to consumer WiFi equipment, RP-SMA is now the dominant connector on commercial WiFi routers, access points, and 2.4/5 GHz antennas.
Common Applications
This RP-SMA and UHF cable assembly is well suited for sensitive receiver chains, spectrum analyzer inputs, and high-EMI environments. The combination of reliable RP-SMA and UHF connectors and custom-cut cable length makes it a practical choice for both field installations and bench setups. Every assembly is hand-terminated, continuity tested, and ships free within the USA.
Frequently Asked Questions
Is this cable hand-assembled in the USA?
Yes. Every CoaxRF cable assembly is hand-terminated and continuity tested at our US facility before shipping. We do not drop-ship pre-made cables from overseas — each cable is built to order.
Can I order a different length than 1 ft?
Yes. This page is for the 1 ft assembly. Use the length buttons above to select a different standard length, or use the Cable Builder for any custom length.
How much signal loss will I see with this 1 ft cable?
At 1800 MHz, RG316DS loses approximately 26 dB per 100 ft. This 1 ft assembly will have roughly 0.26 dB of insertion loss at that frequency. See the signal loss table for all frequency points.
What is the maximum frequency for this assembly?
This assembly is rated DC – 300 MHz. The effective frequency limit is set by the lowest-rated component — either the cable or one of the connectors. Both PL259 UHF Male and RP-SMA FEMALE connectors must be within spec at your target frequency.
What is your return policy?
We accept returns within 30 days of delivery. Custom-length cables are accepted as long as they are in original condition. Contact us and we will provide a prepaid return label at no charge.
